What's going on here guys?
====== GeoSlice Pro 3000 Training Guide ======

This guide provides comprehensive training for the safe and effective use of the GeoSlice Pro 3000 table saw in the geology lab.

===== 1. Introduction =====

The GeoSlice Pro 3000 is a high-precision table saw designed for cutting geological samples. This guide will cover its features, safe operation procedures, and maintenance requirements.

===== 2. Equipment Overview =====

  * Model: GeoSlice Pro 3000
  * Manufacturer: RockTech Industries
  * Key Features:
    * 14-inch diamond-tipped blade
    * 3 HP motor
    * Maximum cutting depth: 4 inches
    * Adjustable cutting speed
    * Water cooling system

===== 3. Safety Precautions =====

  * Always wear appropriate Personal Protective Equipment (PPE):
    * Safety goggles
    * Hearing protection
    * Dust mask
    * Cut-resistant gloves
  * Never operate the saw without the blade guard in place
  * Ensure the water cooling system is functioning before starting a cut
  * Keep the work area clean and free of clutter
  * Never reach across the blade while it's in motion

For complete safety guidelines, refer to the [[107_geology_lab:safety:table_saw_safety|Table Saw Safety Guidelines]].

===== 4. Operating Procedures =====

==== 4.1 Pre-Operation Checklist ====

  - Inspect the blade for damage or wear
  - Check the water reservoir level
  - Ensure all guards and safety features are in place
  - Verify the power cord is in good condition

==== 4.2 Starting the Saw ====

  1. Put on all required PPE
  2. Turn on the water cooling system
  3. Adjust the blade height and angle as needed
  4. Position your sample on the sliding table
  5. Turn on the main power switch
  6. Slowly guide the sample through the blade

==== 4.3 Making a Cut ====

  1. Measure and mark your sample
  2. Secure the sample to the sliding table
  3. Align the marked cut line with the blade
  4. Slowly push the sliding table forward to make the cut
  5. Allow the blade to come to a complete stop before removing the sample

===== 5. Maintenance =====

  * Clean the saw after each use
  * Check and refill the water cooling system daily
  * Inspect and clean the blade weekly
  * Lubricate moving parts monthly
  * Schedule professional maintenance annually

===== 6. Troubleshooting =====

| Problem | Possible Cause | Solution |
| ------- | -------------- | -------- |
| Saw won't start | Power issue | Check power connection and fuses |
| Excessive vibration | Loose or damaged blade | Tighten or replace blade |
| Poor cut quality | Dull blade or incorrect speed | Replace blade or adjust cutting speed |
| Water not flowing | Clogged system or empty reservoir | Clean system or refill water |

===== 7. Emergency Procedures =====

In case of an emergency while operating the GeoSlice Pro 3000, follow these procedures:

==== 7.1 Emergency Shutdown ====

  1. Immediately press the large red emergency stop button located on the front of the saw.
  2. Turn off the main power switch.
  3. Unplug the saw from the power outlet if it is safe to do so.

==== 7.2 Injuries ====

  * For minor cuts:
    1. Stop work immediately.
    2. Clean the wound with the first aid kit located [specify location].
    3. Apply appropriate dressing.
    4. Report the incident to the lab supervisor.

  * For severe injuries:
    1. Call for help immediately. Emergency number: [specify number]
    2. Apply first aid if you are trained to do so.
    3. Do not remove any objects embedded in the wound.
    4. Keep the injured person still and comfortable until help arrives.

==== 7.3 Fire ====

  1. If the fire is small and contained, use the nearest fire extinguisher. Fire extinguishers are located [specify locations].
  2. If the fire is large or spreading:
     * Activate the fire alarm.
     * Evacuate the lab immediately using the nearest exit.
     * Call emergency services: [specify number]
  3. Do not attempt to fight a large fire yourself.

==== 7.4 Power Failure ====

  1. In case of a power failure, the saw will stop automatically.
  2. Turn off the main power switch.
  3. Unplug the saw from the power outlet.
  4. Wait for power to be restored before restarting the saw.

==== 7.5 Reporting ====

All incidents, even minor ones, must be reported to the lab supervisor and documented in the incident report log located [specify location].

===== 8. Additional Resources =====

[This section, previously numbered 7, remains unchanged but is now numbered 8]

Remember, only personnel who have completed this training and received hands-on instruction are permitted to operate the GeoSlice Pro 3000. If you have any questions or need additional assistance, please contact the lab supervisor.

  * [[107_geology_lab:pdf_manuals:geoslice_pro_3000.pdf|GeoSlice Pro 3000 User Manual]]
  * [[107_geology_lab:lab_technician|Contact Lab Technician]]
  * [[107_geology_lab:equipment_maintenance_schedule|Equipment Maintenance Schedule]]

Remember, only personnel who have completed this training and received hands-on instruction are permitted to operate the GeoSlice Pro 3000. If you have any questions or need additional assistance, please contact the lab supervisor.